When purchasing a new watch bracelet, a situation almost always arises in which a metal accessory needs to be adjusted to fit your wrist. Of course, the most ideal option is to seek help from the nearest watch repair service center. Carrying out such a procedure does not require much time, and for a relatively small monetary payment, a qualified specialist will carry out the procedure in your presence. necessary manipulations with a bracelet. In our article we will look at how to remove links on a watch if you want to try it yourself.
Before shortening the strap, you need to measure its length to understand how many elements need to be removed. In order not to make a mistake in performing this procedure, you have to carry out the preparatory work:
Important! If you doubt the exact number of bracelet links to be shifted, then in this case it is better to shorten one less segment. It is much easier to subsequently remove another element of the product than to add it back if the arm circumference was measured incorrectly.
How to remove unnecessary links from a watch? To properly shorten the bracelet, you need to prepare the following tools in advance:
Important! Before you begin the process of shortening the links of a metal bracelet, you must:
- Prepare workplace and make sure your desk is clear of clutter.
- Cover the surface of the table on which we will manipulate the bracelet with a white tablecloth or paper.
- It is also advisable to cover the floor with paper.
This preliminary procedure will allow you to quickly find small parts, and they will not get lost or roll somewhere.
Before removing excess parts, it is necessary to separate the bracelet from the watch, and only after that you can begin to remove the segments.
Let's consider step by step process how to remove links on a watch:
Important! This procedure must be carried out extremely carefully, since with the slightest carelessness the rod can bounce somewhere in the room and get lost.
Important! Also watch out for the small metal tips. Some models of wristwatches have small metal tips at the central point where the links connect, which are removed along with the axis. One wrong move and they could end up on the work surface of the table, or even worse, on the floor.
Important! If the need arises, you need to move the next element to the other side of the bracelet.
Important! The studs must be inserted in the direction opposite to that indicated by the arrows.
Important! If necessary, you need to carefully drive the rod in with a small hammer.
Trying on a watch with a shortened strap:
Important! It is advisable to leave the excess tips and rods and not throw them away, since they can be used in the future.
To remove links from a watch using a screwdriver:
How to remove extra links on a watch:
Important! With this watch model, it is possible to remove excess segments from any part of the bracelet.
Important! They are located on the left side of the upper torsion brackets, which were previously bent.
To remove extra links from a watch bracelet with this strap model:
Important! If everything was done correctly, you will feel the mechanism disengage.
In this article, we told you how to remove links on watches for different models of straps. We hope you were able to do this job carefully, and now your accessory is conveniently and beautifully placed on your hand!
Casio is one of the leaders in the watch movement production market. The company's products are reliable and durable. Among its products you can find both budget models and unique branded products.
The watches of this company are unique products. There are several main features of these structures:
The large size of the buckle on a watch is one of the most common problems encountered when purchasing such a product. This is especially important for models with metal straps consisting of many small links. Decide this problem can be done by shortening the length.
Please note that it is quite possible to perform this operation at home. But if you are not sure that you can properly disassemble the strap, then it is better to take the structure for repair, where they will adjust it to your size.
You can make a Casio watch bracelet smaller at home by following this sequence:
To reduce a link or replace it, you need to pull out the pin connecting two adjacent elements. To do this, use a regular needle to push out the fasteners. Please note that the element is attached to two pins. Therefore, you need to remove both of them to remove the link.
After this, the separated parts are connected to each other. They are fixed using the same pins that need to be inserted into place. Before cutting the links, do not forget to calculate the required number of links that need to be removed.
The design features of watch straps from this manufacturer require the presence of metal links. The shape and size of such parts may be different, but they are connected according to the same principle. Therefore, the technology for shortening such modifications as Casio AMW 700, Edifice, AQW 100d 1avef, Paw 1100, Protrek, G Shock similar to that described in the previous section.
The length of a watch strap can vary over a very wide range. But for each person, an individual value will be considered comfortable. Therefore, when buying a watch, it is important to pay attention to this accessory, which can be made of either leather or metal links.
You can choose the correct bracelet length using several simple methods:
Products Casio enjoys enormous popularity in the world, which leads to the emergence large quantity fakes A low-quality product can be identified by several characteristics:
Most reliable way- go to a watch workshop, where your bracelet will be shortened in 5 minutes and for a price of no more than 150 rubles.
But for people whose hands are trying to grow from the right place, this article was written.
So, new ones came to our table led wristwatch (they are more often called both binary and LED clocks) Zero Kelvin . They have a metal bracelet with standard adjustment. We'll tryshorten the bracelet of this watchinto several segments to fit a 17cm wrist.
Firstly, if the watch is new, do not forget to remove it from bracelet protective film (the film can be temporarily left on the screen and body - it will protect them from accidental contact with the tool).
To shorten the bracelet on our watch, we will need the following tools: an awl, a nut (or bushing or other object with a cavity), and pliers. It is recommended to carry out all work on a comfortable table, laying down a sheet of paper.
So, the watch bracelet consists of fragments (links) connected by pins. To shorten the bracelet, you need to remove several fragments from it. To do this, select the fragment that we will remove. Please note that not all bracelet parts are the same! The first and second segments differ from the rest in shape and we leave them in their places.
We remove the third segment of the bracelet.
Please note that on the inside of the bracelet an arrow indicates the direction in which the fasteners must be removed. We place our bushing under the hole. You can place any hard object with a cavity. Insert an awl into the hole to press out the pin. You can squeeze it out by lightly tapping the awl with a hammer.
Be sure to do this in accordance with the arrow on the bracelet. The pin can be easily removed without the use of a heavy tool. You just have to put pressure on it and it will move from its position.
After the pin has partially emerged from the hole, it can be removed with pliers.
The first stage has been completed.
Now let's do the same with the second pin of the part being removed.
We shortened the watch bracelet by one piece.
Here you just need to try. To begin, shorten your bracelet by a piece and try on the watch. If this is not enough, then shorten the bracelet by one more, etc. But remove the fragments of the bracelet evenly, on each side. If you shorten the bracelet by several segments on only one side, the watch latch will move relative to the bracelet and may cause discomfort to your hand.
We remove one link on the other side of the fastener.
In this example, initially two links were removed, but in the end, for my wrist, I had to remove the third link. How many links and how to shorten the bracelet of your watch- depends on the type of watch you have and your wrist size.
After the extra links are removed, we proceed to assembling the bracelet.
Assembling the bracelet is easier: insert one link into the groove of the other and secure them with a pin. It is inserted with the sharper end, opposite the direction of the arrow on the bracelet.
To prevent the pin from falling out, lightly tap it with a hammer or pliers until it reaches the edge of the bracelet. Don't forget to follow the arrow!
All is ready. As a result, we have a watch, spare links and pins. We definitely check the watch for functionality).
There is never anything “extra” - so save the disconnected links - they will be spare. For convenience, naturally put them together.
Please note that this scheme can be used to shorten the bracelet of most watch models. We hope this article will help you shorten the bracelet on your watch yourself.. But in any case, there are watch workshops that will always help you with this.
P.S. During the reduction of the bracelet on the watch, not a single animal was harmed...)
Good luck! Value your time...
When buying a new watch, people often face the problem of a large bracelet or strap. To make it smaller, simply make an additional hole in the right place. But how to shorten it yourself in a simple way will contact the workshop, where a specialist will adjust the length to required size. But you can do this yourself at home.
There are cases when the bracelet is purchased separately from the watch. To adjust the length in this situation, you must first set it on the watch. Without trying it on, it is impossible to determine whether the links should be removed at all. A slight sagging is allowed within normal limits, and the bracelet does not need to be adjusted.
Ways to adjust the length of the bracelet
Most bracelets have two types of length adjustment. First, you can shorten the watch in the simplest way and change the length of the bracelet by adjusting the lock. To do this, remove the lock ear by simply pressing it and move it to the hole closest to the latch. If the length has changed slightly and the watch is still loose, only removing the extra links will help.
We disassemble the watch bracelet
To perform this rather simple task, you need to prepare a workplace and some tools: an awl, a nut, a hammer and pliers. The links in the bracelet can be attached to each other using pins, screws or studs. When disassembling the bracelet, pins and pins are knocked out or squeezed out, and screws are unscrewed. The diameter of the awl should not be thicker than the hole in which the fastener is located. The diameter of the tool should not exceed the hole in which the fastening element “sits”. Instead of an awl, a gypsy needle, compass or drill of suitable diameter will also come in handy. How to shorten the watch bracelet in this case? To remove the fastener using a needle or drill, you will have to strike with a small hammer.
Before you begin disassembling the bracelet, you need to count the exact number of links from the lock that need to be removed.
How to shorten a watch bracelet and take into account the number of links
When removing links from the bracelet, you should remember the need to maintain symmetry, otherwise the lock of the bracelet will shift to one side, which will cause inconvenience when wearing. The number of elements suitable for removal depends on their size, and is usually limited to five or six pieces on each side. It is better to start reducing the product from the third position, since usually the first two are larger in size. To shorten a watch bracelet, you need to lay it on its side, placing a nut between the links, align the pin or pin that needs to be removed with the hole in the nut.
Using an awl, we squeeze out the connecting pin or pin. On back side The bracelet is usually marked with an arrow indicating the direction of movement. Using pliers will help you remove the fastener completely. Once the pins or studs are pulled out, it will become clear how to shorten the watch bracelet. You just need to connect the remaining parts, making sure that the fasteners fit tightly. In a similar way Almost any bracelet can be adjusted to size. This is not a difficult task, but it requires care so as not to damage the watch itself.
Many consumers, having bought a Casio watch with a metal bracelet, are faced with the fact that hand accessory It just hangs on your wrist. The thing is that manufacturers develop the maximum big size strap to cover all customers. However, this size is not suitable for many people. But don't be upset. Dexterity of hands, just a little free time, a set of simple available tools will help reduce the bracelet on a Casio watch, without the help of a specialist.
So, adjusting the watch bracelet begins with preparing the tools. You will need:
Having opened the strap, you need to carefully examine its inside. During the visual assessment process, you will notice arrows. They indicate the direction in which the metal rods that hold the cells that create the length of the bracelet are pulled out. There are arrows not on all links. Why? Because some parts of the metal strap cannot be disassembled and should not be touched under any circumstances.
Usually the pins that can be removed are located in a small recess. It is into this that you need to insert a needle or another thin object to quickly and carefully remove the bracelet from the watch. Having determined the collapsible elements, you must act according to the following order:
To get it right shorten a Casio watch strap It is important to remove the same number of cells from the halves of the strap. Usually two links are removed from each side. The exact number of dismantled links can be determined by fitting.
All manipulations related to pulling out the rods and dismantling the links must be carried out very carefully. Such scrupulousness will help you maintain the visual appeal of a luxurious bracelet and not break fragile fasteners.
Having removed all unnecessary links, you can begin assembling the strap. This stage The work is as simple as possible. You will have to connect the disparate parts of the strap, securing the broken parts with metal rods. Before you insert the pins, install a bushing at the fastening points - a small cylinder-shaped part, the main task of which is to firmly hold the rod, clamping it in the recess. It is worth considering that all assembly manipulations are carried out in the direction opposite to the arrows. We must not forget about this feature. Only then will you succeed adjust watch strap Casio Right.
You can insert fasteners by hand. After the rod rests against the sleeve, pliers will come to the rescue. They need to lightly press on the rod, pushing it into place. As a last resort, you can knock with a hammer. Everything must be done very carefully, avoiding scratches on the surface of the bracelet.
The strap can be reduced by adjusting the locking clasp. All you need is to rearrange the fixing rod into several compartments. Necessary:
This shortening method allows you to reduce the volume of the bracelet by 0.5 - 2 cm. If this is enough for you, then choose this adjustment method. Now the new Casio will fit perfectly on your hand.